Part 2) Dynamic Views Workflow (11 min)

Report
ProConcrete SS7: Concrete Drawing Production:
An Introduction/Quick-Start, with ‘Best Practices’ Recommendations
© 2014 Bentley Systems, Incorporated
Outline:
Part 1)
Part 2)
Part 3)
Part 4)
ProStructures SS7 Drawing Production Theory
Dynamic Views Workflow
Basic components of Dynamic Views
Dynamic Views and Drawing Composition
(4 min)
(11 min)
(23 min)
(11 min)
Break
Part 5)
Part 6)
Part 7)
Part 8)
2d Rebar: Bar Labeling and Symbolization
(14 min)
3d Modeling Best Practices (to enhance drawing quality and ease-of-use) (11 min)
Printing/Plotting and Publishing to mobile devices
(10 min)
Customization and Dynamic View Setup/project administrator
(4 min)
1h:28m
2 | WWW.BENTLEY.COM | © 2014 Bentley Systems, Incorporated
About:
Approach: All drawing production (no modeling, no schedules).
Build used: PowerProStructures 08.11.11.273 (SS7)
Seed file:
\WorkSpace\ProStructures\Seeds\Imperial3d.dgn
Layout:
This presentation is also available as a .ppt with embedded videos.
Simple model used:
Output:
ProjectPackage.pdf
3 | WWW.BENTLEY.COM | © 2014 Bentley Systems, Incorporated
Outline:
Part 1)
Part 2)
Part 3)
Part 4)
ProStructures SS7 Drawing Production Theory
Dynamic Views Workflow
Basic components of Dynamic Views
Dynamic Views and Drawing Composition
(4 min)
(11 min)
(23 min)
(11 min)
Break
Part 5)
Part 6)
Part 7)
Part 8)
2d Rebar: Bar Labeling and Symbolization
(14 min)
3d Modeling Best Practices (to enhance drawing quality and ease-of-use) (11 min)
Printing/Plotting and Publishing to mobile devices
(10 min)
Customization and Dynamic View Setup/project administrator
(4 min)
4 | WWW.BENTLEY.COM | © 2014 Bentley Systems, Incorporated
Part 1) ProStructures SS7 Drawing Production Theory
• Structural steel Design drawings
(general arrangements), steel
placing drawings, Shop drawings
(AISC shown – similar world-wide):
• Concrete Design drawings and
rebar placing drawings (CRSI
shown – similar world-wide):
“Reinforcing bar placing drawings… provide the details and placing instructions so
that the ironworkers can set the reinforcing bars into place in the formwork”.
5 | WWW.BENTLEY.COM | © 2014 Bentley Systems, Incorporated
Part 1) ProStructures SS7 Drawing Production Theory
• Some structural software products use the same workflow for structural steel
drawings and concrete drawings:
– Structural steel fabrication drawings are a combination of design drawings, single part
drawings + placing drawings.
– Concrete drawing production:
• Design drawings convey design intent of concrete and rebar
• Rebar typically fabricated from bar schedules and/or bar tags
• Rebar placing drawings are for placing rebar and often re-use the design drawings
• Bentley’s Rebar2PC project (2013-2014): Driver: Concrete Drawing Production
– Need to display, label, dimension concrete shapes like a user wants to.
– Need to display, label, dimension rebar like a user wants to.
6 | WWW.BENTLEY.COM | © 2014 Bentley Systems, Incorporated
Part 1) ProStructures SS7 Drawing Production Theory
• Structural steel: DetailCenter
• Concrete: Dynamic Views and
Hypermodeling
7 | WWW.BENTLEY.COM | © 2014 Bentley Systems, Incorporated
Part 1) ProStructures SS7 Drawing Production Theory
• Beginning with (Power) ProStructures SS7: Dynamic Views are the
recommended best-practice method for producing drawings for concrete and
rebar drawings.
• DetailCenter remains the recommended best practice to produce steel fabrication
drawings (and remains an option for concrete drawing production as well). Note:
for precast concrete panels and other similar concrete objects, DetailCenter may
be the best option.
8 | WWW.BENTLEY.COM | © 2014 Bentley Systems, Incorporated
Part 1) ProStructures SS7 Drawing Production Theory
ProConcrete SS7 provides two methods of displaying 3D rebar in drawings:
1) 2D views of the 3D rebar without any symbolization (drawing on left below)
2) 2D symbolic graphics (drawing on right below)
Drawing with 3D rebar shown
9 | WWW.BENTLEY.COM | © 2014 Bentley Systems, Incorporated
Drawing with 2D symbolic rebar shown
Outline:
Part 1)
Part 2)
Part 3)
Part 4)
ProStructures SS7 Drawing Production Theory
Dynamic Views Workflow
Basic components of Dynamic Views
Dynamic Views and Drawing Composition
(4 min)
(11 min)
(23 min)
(11 min)
Break
Part 5)
Part 6)
Part 7)
Part 8)
2d Rebar: Bar Labeling and Symbolization
(14 min)
3d Modeling Best Practices (to enhance drawing quality and ease-of-use) (11 min)
Printing/Plotting and Publishing to mobile devices
(10 min)
Customization and Dynamic View Setup/project administrator
(4 min)
1h:28m
10 | WWW.BENTLEY.COM | © 2014 Bentley Systems, Incorporated
Part 2) Dynamic Views Workflow
Definition of “Dynamic Views”: (source: MicroStation Help file):
Dynamic Views is a general name that encompasses several related technologies
which share a common goal of making model analysis and documentation more
interactive and intuitive.
Gone are the days when designs were just static [snapshot] views. They are
replaced by the ability to create live, intelligent sections of a design composition that
update automatically (through the use of detailing symbols with fields and links) as
the design evolves.
11 | WWW.BENTLEY.COM | © 2014 Bentley Systems, Incorporated
Part 2) Dynamic Views Workflow (Terms)
Dynamic Views: Terms and Definitions
Design
Drawing
Model
12 | WWW.BENTLEY.COM | © 2014 Bentley Systems, Incorporated
Sheet
Annotation
Part 2) Dynamic Views Workflow (Terms)
Dynamic Views: Terms and Definitions
Design
Drawing
Model
Design Model:
Drawing Model:
Sheet Model:
13 | WWW.BENTLEY.COM | © 2014 Bentley Systems, Incorporated
Sheet
Annotation
The 3D BIM model (.dgn)
A 2D model container in which a
Dynamic View is stored.
A 2D or 3D model container that typically
includes a referenced sheet border.
Part 2) Dynamic Views Workflow (Terms)
Dynamic Views: Terms and Definitions
Design
Drawing
Model
Design Model:
Drawing Model:
Sheet Model:
14 | WWW.BENTLEY.COM | © 2014 Bentley Systems, Incorporated
Sheet
Annotation
Part 2) Dynamic Views Workflow (Terms)
Dynamic Views: Terms and Definitions
Design
Drawing
Model
Sheet
Annotation
Design Annotation: 3D labels, model annotation
Drawing Annotation: Labels, dimensions, notes, callouts
appropriate for a drawing (includes 2D
symbolic rebar labels and dimensions)
Sheet Annotation: Only the notes, labels, callouts appropriate for
a sheet (general notes, sheet name)
15 | WWW.BENTLEY.COM | © 2014 Bentley Systems, Incorporated
Part 2) Dynamic Views Workflow (Terms)
Dynamic Views: Terms and Definitions
Design
Drawing
Model
Sheet
Annotation
Design Annotation: 3D labels, model annotation
Drawing Annotation: Labels, dimensions, notes, callouts
appropriate for a drawing (includes 2D
symbolic rebar labels and dimensions)
Sheet Annotation: Only the notes, labels, callouts appropriate for
a sheet (general notes, sheet name)
16 | WWW.BENTLEY.COM | © 2014 Bentley Systems, Incorporated
Part 2) Dynamic Views Workflow (Terms)
Dynamic Views: Terms and Definitions
Design
Drawing
Model
Sheet
Annotation
Design Annotation: 3D labels, model annotation
Drawing Annotation: Labels, dimensions, notes, callouts
appropriate for a drawing (includes 2D
symbolic rebar labels and dimensions)
Sheet Annotation: Only the notes, labels, callouts appropriate for
a sheet (general notes, sheet name)
17 | WWW.BENTLEY.COM | © 2014 Bentley Systems, Incorporated
ProConcrete Workflow (Modeling)
3D DGN File
18 | WWW.BENTLEY.COM | © 2014 Bentley Systems, Incorporated
Parent
• All Rebar in ProConcrete must belong to a
concrete object - either a ProConcrete
parametric object or a promoted solid.
• In the SS7 release, the 3D Rebar and the
concrete object must be placed in the same
DGN file.
• Rebar may protrude outside the extents of it’s
owner concrete (including entirely outside), and
may extend over multiple other concrete objects.
• Concrete and Rebar objects both have their own
levels( ) colors, line weights, etc.
Child (both reside in same DGN file)
Dynamic Views Workflow (ProConcrete)
3D DGN File
• All Drawing models with 2D symbolic rebar
must be saved to the 3D DGN file
containing the concrete and rebar.
Leave this turned OFF
if you want 2D symbolic
rebar in DV’s.
19 | WWW.BENTLEY.COM | © 2014 Bentley Systems, Incorporated
Dynamic Views Workflow (ProConcrete)
3D DGN File
• Drawing models with no 2D symbolic rebar
(3D only*) may be sent to another file
OK to use
Drawing Model DGN File
20 | WWW.BENTLEY.COM | © 2014 Bentley Systems, Incorporated
* see speaker notes
Dynamic Views Workflow (ProConcrete)
Real-world Project Workflow:
Project 2015:001
DGN File 1
DGN File 2
DGN File 3
BIM Composite DGN
•
•
•
•
•
•
21 | WWW.BENTLEY.COM | © 2014 Bentley Systems, Incorporated
Material lists/QTO
Bar bending schedules
Schedule simulation
Clash detection
Printing/Plotting/
Publishing
Mobile app export
Dynamic Views Workflow (ProConcrete)
Real-world Project Workflow:
Project 2015:001
DGN File 1
DGN File 2
DGN File 3
BIM Composite DGN
•
•
•
•
•
•
Material lists/QTO
Bar bending schedules
Schedule simulation
Clash detection
Printing/Plotting/
Publishing
Mobile app export
Sheet Composite DGN
22 | WWW.BENTLEY.COM | © 2014 Bentley Systems, Incorporated
Dynamic Views Workflow (ProConcrete)
Real-world Project Workflow:
Project 2015:001
DGN File 1
DGN File 2
DGN File 3
BIM Composite DGN
•
•
•
•
•
•
Material lists/QTO
Bar bending schedules
Schedule simulation
Clash detection
Printing/Plotting/
Publishing
Mobile app export
Sheet Composite DGN
23 | WWW.BENTLEY.COM | © 2014 Bentley Systems, Incorporated
Dynamic Views Workflow (ProConcrete)
Real-world Project Workflow:
Project 2015:001
DGN File 1
DGN File 2
DGN File 3
BIM Composite DGN
•
•
•
•
•
•
24 | WWW.BENTLEY.COM | © 2014 Bentley Systems, Incorporated
Material lists/QTO
Bar bending schedules
Schedule simulation
Clash detection
Printing/Plotting/
Publishing
Mobile app export
Dynamic Views Workflow (ProConcrete)
Another real-world Project Workflow:
Project 2015:002
DGN File 2
DGN File 1
DGN File 3
BIM Composite DGN
•
•
•
•
•
•
DV’s with 2D symbolic rebar
Sheet
Composite
DGN
25 | WWW.BENTLEY.COM | © 2014 Bentley Systems, Incorporated
Material lists/QTO
Bar bending schedules
Schedule simulation
Clash detection
Printing/Plotting/
Publishing
Mobile app export
DV’s without 2D symbolic rebar (3d rebar only)
Outline:
Part 1)
Part 2)
Part 3)
Part 4)
ProStructures SS7 Drawing Production Theory
Dynamic Views Workflow
Basic components of Dynamic Views
Dynamic Views and Drawing Composition
(4 min)
(11 min)
(23 min)
(11 min)
Break
Part 5)
Part 6)
Part 7)
Part 8)
2d Rebar: Bar Labeling and Symbolization
(14 min)
3d Modeling Best Practices (to enhance drawing quality and ease-of-use) (11 min)
Printing/Plotting and Publishing to mobile devices
(10 min)
Customization and Dynamic View Setup/project administrator
(4 min)
26 | WWW.BENTLEY.COM | © 2014 Bentley Systems, Incorporated
Part 3) Basic Components of Dynamic Views:
3-1:
Clip volumes and Fitted Sections:
• Clip Volume toolbox or window tool box (right click if not displayed)
• CV’s are construction elements and have levels, right-click Apply
• Handles, right-click/flip direction, stepped section clip volumes
3-2:
Named Fences from Clip Volumes
• View attribute – Clip Volume on/off
3-3:
Clip Volume View Attributes:
• Display styles for Forward, Back, Cut, Outside
3-4:
3-5:
3-6:
Create Drawing from Clip Volume
Reference Files (learn Activate/Deactivate),
View groups, Models, Saved views (review)
27 | WWW.BENTLEY.COM | © 2014 Bentley Systems, Incorporated
Outline:
Part 1)
Part 2)
Part 3)
Part 4)
ProStructures SS7 Drawing Production Theory
Dynamic Views Workflow
Basic components of Dynamic Views
Dynamic Views and Drawing Composition
(4 min)
(11 min)
(23 min)
(11 min)
Break
Part 5)
Part 6)
Part 7)
Part 8)
2d Rebar: Bar Labeling and Symbolization
(14 min)
3d Modeling Best Practices (to enhance drawing quality and ease-of-use) (11 min)
Printing/Plotting and Publishing to mobile devices
(10 min)
Customization and Dynamic View Setup/project administrator
(4 min)
28 | WWW.BENTLEY.COM | © 2014 Bentley Systems, Incorporated
Part 4) Dynamic Views and Drawing Composition
4-1:
4-2:
4-3:
4-4:
4-5:
Drawing composition commands
Drawing creation and Sheet creation
Dynamic Views and Project Explorer
Add a Drawing view to an existing sheet
Modifying the drawing scale
29 | WWW.BENTLEY.COM | © 2014 Bentley Systems, Incorporated
Outline:
Part 1)
Part 2)
Part 3)
Part 4)
ProStructures SS7 Drawing Production Theory
Dynamic Views Workflow
Basic components of Dynamic Views
Dynamic Views and Drawing Composition
(4 min)
(11 min)
(23 min)
(11 min)
Break
Part 5)
Part 6)
Part 7)
Part 8)
2d Rebar: Bar Labeling and Symbolization
(14 min)
3d Modeling Best Practices (to enhance drawing quality and ease-of-use) (11 min)
Printing/Plotting and Publishing to mobile devices
(10 min)
Customization and Dynamic View Setup/project administrator
(4 min)
30 | WWW.BENTLEY.COM | © 2014 Bentley Systems, Incorporated
Part 5) 2d Rebar: Bar labeling and symbolization
Pre 5.0: Bar Marking (Positioning)
5-1:
5-2:
5-3:
Rebar graphics: 2d and 3d
2d Rebar labeling and symbolization – (activate the drawing, work in the sheet)
Dimensions, annotations, notes:
• Drawing annotation: (activate the drawing, work in sheet)
• Sheet annotation: (general notes, etc)
31 | WWW.BENTLEY.COM | © 2014 Bentley Systems, Incorporated
Outline:
Part 1)
Part 2)
Part 3)
Part 4)
ProStructures SS7 Drawing Production Theory
Dynamic Views Workflow
Basic components of Dynamic Views
Dynamic Views and Drawing Composition
(4 min)
(11 min)
(23 min)
(11 min)
Break
Part 5)
Part 6)
Part 7)
Part 8)
2d Rebar: Bar Labeling and Symbolization
(14 min)
3d Modeling Best Practices (to enhance drawing quality/ease-of-use) (11 min)
Printing/Plotting and Publishing to mobile devices
(10 min)
Customization and Dynamic View Setup/project administrator
(4 min)
32 | WWW.BENTLEY.COM | © 2014 Bentley Systems, Incorporated
Part 6) 3d Modeling-Best Practices (for best Concrete Drawings)
6-1:
6-2:
6-3:
6-4:
6-5:
S7 provides new rebar levels, new level filters, new colored rebar patterns
Item Browser (and publish iModel)
Isolate command
Display Sets & Named Groups
Hypermodeling
• Use: Levels, Level filters and Item Browser
• Do not use: ProStructures Display Classes or Area Classes with rebar:
– They do not allow different display settings in multiple Dynamic Views
– Do not work across MicroStation reference files
– File corruptions have been encountered in large models
33 | WWW.BENTLEY.COM | © 2014 Bentley Systems, Incorporated
Outline:
Part 1)
Part 2)
Part 3)
Part 4)
ProStructures SS7 Drawing Production Theory
Dynamic Views Workflow
Basic components of Dynamic Views
Dynamic Views and Drawing Composition
(4 min)
(11 min)
(23 min)
(11 min)
Break
Part 5)
Part 6)
Part 7)
Part 8)
2d Rebar: Bar Labeling and Symbolization
3d Modeling Best Practices (to enhance drawing quality/ease-of-use)
Printing/Plotting and Publishing to mobile devices
Customization and Dynamic View Setup/project administrator
34 | WWW.BENTLEY.COM | © 2014 Bentley Systems, Incorporated
(14 min)
(11 min)
(10 min)
(4 min)
Part 7) Printing/Plotting and Publishing to Mobile Devices
7-1:
7-2:
7-3:
7-4:
7-5:
7-6:
Visible Edges: Dynamic vs. Cached
Printing/plotting
Batch printing/plotting with Print Organizer
Creating a PDF with drawings,
3d model, bar schedules
Publishing an iModel, publishing a
mobile iModel for viewing on iPad/iPhone
Automatically update output every time
I exit a model?
35 | WWW.BENTLEY.COM | © 2014 Bentley Systems, Incorporated
Outline:
Part 1)
Part 2)
Part 3)
Part 4)
ProStructures SS7 Drawing Production Theory
Dynamic Views Workflow
Basic components of Dynamic Views
Dynamic Views and Drawing Composition
(4 min)
(11 min)
(23 min)
(11 min)
Break
Part 5)
Part 6)
Part 7)
Part 8)
2d Rebar: Bar Labeling and Symbolization
3d Modeling Best Practices (to enhance drawing quality/ease-of-use)
Printing/Plotting and Publishing to mobile devices
Customization and Dynamic View Setup/project administrator
36 | WWW.BENTLEY.COM | © 2014 Bentley Systems, Incorporated
(14 min)
(11 min)
(10 min)
(4 min)
Part 8) Customization: Setup/Project Administrator
8-1:
8-2:
8-3:
8-4:
8-5:
8-6:
Customizing your own Drawing Seeds (.dgnlib)
Customizing your own Detailing Symbol Styles (.dgnlib)
Customizing your own Display Styles (.dgnlib)
Rebar: Default.def
Rebar: Display.sys
Rebar: Presets.sys
37 | WWW.BENTLEY.COM | © 2014 Bentley Systems, Incorporated
End
38 | WWW.BENTLEY.COM | © 2014 Bentley Systems, Incorporated

similar documents