Introducing our range of Water Hydraulic Valves • For control of Main Inlet Valve Servo motor, service & maintenance seals • • • Pressures up to 120 bar Flow rates up to 600 litres/min 316L Stainless Steel Construction Water Hydraulic Control Valves The 6mm Water Hydraulic Control valve is a ball seated type valve. The stainless steel / ceramic ball seat design ensures a virtual leak tight shut off. • • • • M.T.B.F., SFF, PFD and SIL Data (Available upon request) Easy Installation, Repair and Replacement Stainless Steel Construction Up to 120 bar Operating Pressure Range General Description The DN6 valve design incorporates a balanced internal piloting system and a lever mechanism to enable a wide range of operators to operate the valve. All valves have an ‘O’ Ring interface that enables them to be fitted with BSP.P ported subplates as standard, or manifold mounted to reduce pipework, fittings, weight and space. This interface also allows direct mounting of the valve to larger pilot operated valves up to the DN25, increasing the flow capacity to 200 l/min. By removing just 4 bolts the valves can be dismounted without disturbing pipework and possibly contaminating the hydraulic system. Blanking and flushing plates can also be supplied. Water Hydraulic Control Valves Construction Materials bodies and subplates: 316L Stainless Steel • Valve parts: Various grades of Stainless • Wetted Steel/Super Duplex / Ceramic/Aluminium Bronze Nitrile / Buna N / PTFE / Polyurethane • Seal A4, grade 80 stainless steel • Fasteners: Springs: stainless steel • Operating Temperature Range • Standard: 5 ºC to + 60 ºC Ingress Protection (solenoids valves ) • IP54 Operating Pressure Range • 15 to 120 bar Operating Medium • Filtered Fresh Water Recommended Filtration 10 microns • DN6: • DN15: 25 microns 25 microns • DN25: DN40: 200 microns • Water Hydraulic Control Valves Hydraulic Pilot Operated • 2 port, 2 position 2 position • 315port, to 120 bar pressure range • • Flow rates up to 20 l/min Steel construction • Stainless Pilot media, Oil or Water • Plunger or Roller Cam Operated • 2 port, 2 position 2 position • 315port, to 120 bar pressure range • Flow rates up to 20 l/min • Stainless Steel construction • Solenoid Operated with Hydraulic Override Pilot • 2 port, 2 position port, 2 position • 3120 bar max. pressure • Flow rates up to 20 l/min • Stainless Steel construction • 24VDC, 110VDC, 220VDC • • Override signal, oil or water Water Hydraulic Control Valves Solenoid Operated • 3 port, 2 position rates up to 20 l/min • Flow 15 to 120 bar working pressure • Stainless Steel construction • DN15 & DN25 • Solenoid operated or Water pilot operated • Oil 3 port, 2 position • • 4 port, 2 position range 15 to 120 bar • Pressure Flow rates up to 200 l/min • Stainless Steel construction • media, Oil or Water • Pilot Easily replaceable one piece cartridge • valve design DN40 - Hydraulic Pilot Operated • 3 port, 2 position port, 2 position • 5Pressure range 15 to 120 bar • Flow rate up to 600 l/min • Stainless Steel • Pilot media, Oilconstruction or Water • • Remote position sensors ½ “ SAE 3000 psi Flanged • 1connections or BSP.P threaded ports before bleed function • Block Operating temperature range • 5 ºC to + 60 ºC Water Hydraulic Control Valves Keep it simple ! Water Hydraulic Control Valves can simplify hydraulic control circuits and therefore increase reliability, while reducing maintenance and capital costs. Water Hydraulic Control Valves can replace conventional oil hydraulic power units and oil servo valves by utilizing the valuable natural renewable energy resource of water.