Document

Report
NEW or UPDATED PRODUCTS
1st Quarter 2015
Revision – 2015-02-24
HANBELL SCREW COMPRESSORS
Variable
Frequency
Drive
Hanbell Screw
Compressor
• Hanbell Screw Compressors
with Yaskawa Variable
Frequency Drivers
Hanbell Oil
• Available in One Gallon or
5 Gallon pails
HANBELL OPEN DRIVE
SCREW COMPRESSORS
 Hanbell Open Type screw compressors feature
simple design and robust construction
 5 models with displacement for 228/134 to
1521/895 m3/hr/CFM (60 hz)
 Low noise, minimized vibration, high reliability, and durability
 Long life bearings using a combination of 11 axial and radial bearings, this gives the
compressor excellent bearing life and reliability
 Field adjustable Volume Ratio (VI) Important in achieving the best efficiency by stopping
over/under compression
 Precise capacity control, either four step 25%, 50%, 75%, 100% or step less (infinite).
External capacity indicator (available)
 Economizer operation with floating ECO port, works at partial load to full load
 While the RG series open compressor was developed for ammonia it also operates
equally well on HFC and HCFC refrigerants R134A, R404A, R407C, R22,
R717,R290 (Propane) - Others refrigerants available
 Additional cooling with liquid/oil injection at
the compressor
MCS-MAGNUM-DOOR-NEMA4
The MAGNUM just got BETTER
Keypad showing
new design,
adding RS-485
connection
New Gasket
provides the unit
with a NEMA 4
rating

The MCS-MAGNUM-DOOR-NEMA4 Keypad has been sealed in its own frame using a new
Gasket (BISCO HT-800 Medium Cellular Silicone). The RS-485 port has been added to the back of
the Keypad. Moving the communicating port to the back, adding the new gasket, provides the unit
with a NEMA4 rating. Operating Temperature -4°F to +158°F (-20°C to +70°C).

The MCS-MAGNUM-DOOR-NEMA4 can be mounted in existing units as a retrofit or in a new
installation where a waterproof Keypad may be needed. The unit has been tested outdoors at our
Fort Myers facilities and has proven to be very effective.
MCS-USB-RS485

The MCS-USB-RS485 Serial Converter Cable
provides a fast simple way to connect to MCS
controllers, such as the MCS-MAGNUM or the
MCS-MICROMAG. The cable can be used to
connect the new Touchscreens to these controllers.

The MCS-USB-RS485 cable contains a small
internal electronic circuit board, utilizing the FT232R,
which is encapsulated into the USB connector end of
the cable. Each cable supports the FTDIChip-ID™
and is equipped with a unique USB serial number
programmed into
the FT232R.
MCS-MAGNUM-FIRMWARE V17
Added New Features
 LOOKUP TABLES- added 5 tables with max of 21
entries per table.
 CENTRIFUGAL – VARIABLE GEOMETRY DIFFUSER
 SUBCOOLER EXV CONTROL
 MANUAL % CONTROL FOR COMPRESSOR
 Modbus Analog Output writes
MCS-MODBUS-IO
The MCS-MODBUS-I/O gives the MCS-MAGNUM
the ability to act as a Modbus Master using the
Modbus RTU Protocol. This allows the MCS-MAGNUM
to communicate to Modbus slave devices (such as
Variable Frequency Drives, Compressors, etc.) to send
and access parameters. The MCS-MODBUS-I/O
performs like a MCS-RO10 and MCS-SI16-AO4 to the
MCS-MAGNUM.
New

Add support for:
 Danfoss VFD
 Bitzer Built-In VFD
 Copeland True VFD Scroll
MCS-TOUCH-7
MCS-TOUCH-15.4
VIEWING and using the MCS-MAGNUM
Just got EASIER



The MCS-TOUCH-7 and the MCS-TOUCH-15.4 are
suitable for installation for both indoor and outdoor
applications. Utilizing a gasket for an environment seal
provides the unit with a NEMA 4 rating.

The MCS-TOUCH-7 and the MCS-TOUCH-15.4 are
new touchscreen interfaces designed to simplify user
access with the MCS-Magnum and MicroMag utilizing
MCS-Connect to provide both graphics and service
mode access to technicians.
The MCS-TOUCH-7 and the MCS-TOUCH-15.4 can connect up to 60 MCS controllers at once
and supports RS485 or Ethernet networking.
The MCS-TOUCH-7 and the MCS-TOUCH-15.4 makes it easy for the user to manage more
complex installations, without losing the overall view of the installation, as well as ensuring that
the pages can be browsed in a fast and straightforward manner.
MCS-CONFIG- New Features

MCS-Config software is part of the MCS Support
System. Its purpose is to build the configuration files
for the MCS micro controllers. Through this program
information relating to the particular installation such
as the points list, set points and control strategies
are specified. Once a configuration file has been
built it can be uploaded into a live system using the
transmit function found in the MCS-Connect.
 Added option in File Menu to convert from V17 to V17 Config Structure
 Added Lookup Table support to the main option bar that go with a
new SI and AO lookup table type
 Alphabetized the Display Type List on the SI Info Screen
 Added an AO Modbus Write Type to the AO Info Screen
MCS-CONNECT- New Features
MCS-Connect allows the user to monitor the status
of the micro controller in real time and with proper
authorization changes can be made to the system.
 Added support for V17 Config Structure
 Added support for Headers in the new XML
Graphics Package
 Added support for four part Animated Graphics in the new XML Graphics Package
 Implemented new Swing Based Layers for the new XLM Graphics Package
 Added Subcooler EXV grid that will show between the EXV and Superheat Grids
MICROMAG

The MicroMag is a rugged microprocessor based
controller designed for the hostile environment of the
HVAC/R industry. It is designed to be the primary
manager of the package it is controlling. The MicroMag
provides flexibility with set points and control options that
can be selected prior to commissioning a system or
when the unit is live and functioning. Displays, alarms
and other interfaces are accomplished in a clear and
simple language that informs the user as to the status of
the controller.
 The MicroMag is designed to control up to 4 circuits with
1 compressor each. Complementing the MicroMag
controller are two expansion boards (MICROS18-A04
and MICRORO6) that allow up to a maximum of 18
Relay Outputs, 1 Triac Output, 26 Sensor Inputs and 12
Analog Outputs. Communication to these units occur at
38,400 baud over the MCS-I/O port which is dedicated
for this purpose.
 Add EXV support
Expansion
Boards for
MicroMag
MICRORO6
MICROSI8-AO4
MCS-THERMOSTAT

MCS announces a new MCS-THERMOSTAT for the
MicroMag that offers contractors and OEMs simple set-up
and operation. The unit is installed in the zone allowing easy
access.
 This user friendly interface allows the viewing of 17 different
parameters and has the ability to change 9 adjustable settings
including cooling & heating system set points, operational
schedules, holiday schedules, calibration and password
protection.
 The MCS-THERMOSTAT is powered from the MCS controller’s +5vdc supply via a 4 wire
connection that can be wired with the communication network cabling in addition.
 The MCS-THERMOSTAT screen displays seven icons reporting operational mode and
status at a glance. These include alarm conditions that will be displayed on the LCD display
using a on-screen icon along with an audible alarm. The alarm condition can be silenced
and reset from the MCS-THERMOSTAT, avoiding the need to visit the MCS controller.
MCS-ZONE-II

An extremely reliable sensor packaged in a
very durable aesthetic package. The sensor
is potted with a thermally conductive
adhesive to guarantee durability and
response, its high accuracy allows for
interchangeability in the field.
 The large resistance range allows the
use of over 1000’ of cable with no
noticeable effect.
Part # MCS-ZONE-OVR-RST
(Pictured with Override & Reset Options Included)
Options
-OVR Pressing the Override button for 2 sec results in the system going from
unoccupied to occupied mode for the time that was setup in the override set point.
-RST Pressing the Reset button for 2 sec decreases the Target & pressing it
for 6 sec increases the Target. Targets are restored to original set points at
Midnight.(Only for MicroMag)
MCS-HUMD-II

The Temperature Humidity zone mounted sensor is supplied
in an attractive package which can be mounted on standard
USA or Overseas electrical boxes. The package includes
rubber wire grommets that eliminate any draft influence on
the sensors. Both the temperature and humidity sensors are
the MCS highly reliable sensors with accuracy, durability and
extremely fast response time.
 The large resistance range allows the use of over 1000’ of
cable with no noticeable effect. The table below provides a
cross reference between °F/°C, OHMS, and VOLTS DC at the
sensor input pin (S1)
on the MCS controller.
 The humidity sensor outputs a linear signal and is a low power
device (200µA typical @ 5vdc). Because of its interchangeability,
quality and reliability it is used in commercial, industrial, military,
and aerospace applications.
OPTIONS:
OVR Pressing the Override button for 2 sec results in the system going from
unoccupied to occupied mode for the time that was setup in the override set
point.
-TR Pressing the Reset button for 2 sec decreases the target & pressing it for 6 sec
increases the Target. Targets are restored to original set points at Midnight. (Only for
MicroMag)
MCS-HUMD-II-OVR-TR
(Pictured with Override & Target
Reset Options Included)
MCS-WIRELESS-3G

Broadband Router with Integrated Verizon 3G Modem
(Only for use in USA)

The MCS-WIRELESS-3G is built for your
network. It’s a highly-featured, compact router
designed for critical industrial applications that
require 24x7 connectivity.

The router features a built-in high-speed Verizon 3G
EVDO modem. Supplied with one year subscription to
MCS Wireless Verizon Data Plan, 250MB per month.

The MCS-WIRELESS-3G is a powerful tool that is especially useful in locations
where there is no readily available internet connection. Combined with the data plan,
the MCS-WIRELESS-3G may be used to wirelessly connect to the MCS-MAGNUM
wherever a cellular signal is found.

You will receive everything you need to setup communication with an MCS Controller,
one year Verizon 250MB per month data plan and a crossover Ethernet cable to link
the MCS-WIRELESS-3G to the MCS Controller board.

MCS also offers an MCS-WIRELESS-ROUTER-No Modem, for users who like the idea of
wireless connection but want to supply their own Broadband Modem and Data Plan.
NOTE: The MCS-WIRELESS-3G can be used to
communicate with multiple MSC Controllers.
Email: [email protected] for more information.
MCS-EXV-DRIVER
 The MCS-EXV-DRIVER is used for the positioning and control of bipolar
expansion valves using an analog input of 0-10 VDC (0 VDC = 0% valve
opening, 10 VDC = 100% valve opening).
 The MCS-EXV-DRIVER-XX supports multiple electronic valve
manufacturers including Sporlan, Alco, Danfoss and Carel.
 The MCS-EXV-DRIVER also supports overdriving on full opened and full
closed voltage signals.
 Adds support for Carel Valves
MCS-EXPANSION VALVE
MCS-TRANSDUCERS

The MCS-TRANSDUCERS are one of the most economic and durable
options on the market for dealing with high-pressure industrial applications.

In addition to being CE and UL approved, the MCS-TRANSDUCERS are
capable of surviving high vibration. They includes a cavity built out of solid 17-4
PH stainless steel ¼” SAE Female Flare fitting & Schrader valve; 7/16-20 UNF
pipe thread which creates a leak-proof, all metal sealed system that makes the
MCS-TRANSDUCERS ideal for use with rugged HVAC environments.
MCS-150
MCS-200
MCS-250
MCS-500
MCS-667
CT Series Sensors
MCS-CT300

Monitors current flowing to electrical
equipment.

Solid-core; the conductor runs through
the sensor

No cutting, taping or rerouting is required

UL Approved
 Converts current magnitude to a linear output voltage
between 0 and 5 Vdc which can be read as a standard
analog input signal.
The signal is used by MCS micro
controllers for:
 Slide valve control on screw machines
 High amp motor overload protection
 Verification of device on / off
MCS-CT500
The MCS-STATIC-0.2”-B

The MCS-STATIC-0.2” is a differential (static) pressure
transducer that is designed to handle dry air or nonconducting
gas. It accepts 4.8 to 8.1vdc and 14.5 to 17vdc for input power
and outputs a 0.5 to 4.5vdc signal which is proportional to 0.0
inches to 0.2 inches of water column (WC).
 The MCS-STATIC-0.2” differential pressure transducer is
designed to measure building static pressure in order to
control exhaust fans.
 The MCS-TUBE can be epoxied to a discharge or suction
line in order to obtain temperature readings without the use
of a well. It was designed to be used with the MCS-T100
temperature sensor and comes pre-filled with heat
conductive compound.
MCS-MAGNUM Control Cabinets
Factory Assembled & Tested Control Cabinets
MCS-MAGNUM CONTROL
CABINET W/ KEYPAD & LCD
 MCS Control Board –
mounted with prewired power &
communication
 Input Power -Terminal strip,
Circuit Breaker, power outlet
 Indicator Lights – Alarm,
Warning, & Compressor Status
 Switches – Emergency Stop,
Unit Hand/Off/Auto, &
Compressor Disable
MCS-MAGNUM CONTROL
CABINET W/ TOUCH SCREEN
For additional information please visit our website
www.mcscontrols.com
Or call MCS at 239-694-0089
5580 Enterprise Pkwy.
Fort Myers, FL 33905
Office: 239-694-0089
Fax: 239-694-0031
www.mcscontrols.com

similar documents