Smart Board

Report
Smart Board
Troubleshooting
2
SMART
Board 600
and D600
Series
 The User Guide contains useful information such as installing,
connecting, maintaining, and troubleshooting your Smart
Board.
 Please refer to it when you are installing your Smart Board for
the first time or connecting a new computer to your Smart
Board.
http://tinyurl.com/SBUserGuide
3
SMART
Board 600
and D600
Series
 If your projector isn’t installed in a fixed location, you can
correct many image problems by shifting your projector or
adjusting its zoom lens.
 Complete the following steps only as required.
1. If the left and right edges of the projected image aren’t parallel, raise or
lower your projector at the front or back until the edges are parallel.
2. If the top and bottom edges aren’t parallel, turn the projector slowly
until the edges are parallel.
4
SMART
Board 600
and D600
Series
3. Adjust the image size by moving the projector forward or backward to
increase or reduce the image size, until it correctly fills the screen.
4. Make fine adjustments to the image level and size according to your
projector manufacturer’s instructions.
5. Create a clear image by adjusting your projector’s focus function.
5
SMART
Board 600
and D600
Series
 If your Smart Board behaves erratically or becomes unresponsive, you
might be able to restore normal operation by resetting your Smart
Board.
 First, try to reset your Smart Board by disconnecting and then
reconnecting the USB cable.
 This step turns the power off and back on, resetting all components.
6
SMART
Board 600
and D600
Series
 If reconnecting the cables didn’t work, use the tip of a pen tray pen
to press the Reset button.
The Reset button is on the side of your Smart Board. It lets you reset
the controller if the Smart Board stops responding or is in the
wrong mode.
7
SMART
Board 600
and D600
Series
 You can see the Ready light in the lower-right corner of your
Smart Board’s frame.
 The Ready light indicates the Smart Board’s operating status.
8
SMART
Board 600
and D600
Series
Ready Light State
Meaning
Solid Red
Your Smart Board is receiving power, but it isn’t
communicating with your computer.
Solid Green
Your Smart Board is receiving power and is
communicating successfully with SMART Product
Drivers and your computer.
Flashing Green
Your Smart Board is receiving power and is
communicating successfully with your computer’s
operating system. Tools such as the pens, eraser,
keyboard, and help button don’t work.
Flashing or Solid Amber
The controller module is in a service mode or has
detected a software error.
9
SMART
Board 600
and D600
Series
 If you experience a problem with your Smart Board, you can
troubleshoot it by using the Ready light, in conjunction with
other observable symptoms and behaviors.
 The User Guide includes flow charts that help you to diagnose
the issues and help you solve the problem.
These flow charts are easy to follow and extremely helpful.
Refer to pgs. 42 – 46 of the User Guide for the Flow Charts.
10
SMART
Board 600
and D600
Series
 If the Ready light indicates that your Smart Board is
operating normally, but you’re still experiencing
problems, refer to the troubleshooting tips in the
table on the next few slides.
11
SMART
Board 600
and D600
Series
Symptom/Observation
There’s no image projected
on your Smart Board’s screen,
or a “No Input” message
appears.
Cause
Solution
Your projector isn’t
receiving a video signal.
 Check the video cable connections.
 Check that the correct video input is selected
on your projector.
 Make sure that your projector is on and that
it’s connected to a power source.
 If you’re using a laptop computer, switch the
external video connection on. Refer to your
laptop’s user’s guide for more information.
Your computer is in
standby mode.
 Move the mouse or touch any key on your
keyboard to bring your computer out of standby
mode.
Your computer is off.
 Turn on your computer and then log on as usual.
12
SMART
Board 600
and D600
Series
Symptom/Observation
Cause
Solution
The projected image is blurry,
Your projector’s position,  Adjust your projector’s position, zoom and
too large or doesn’t completely zoom and focus settings
focus settings.
fill your Smart Board’s screen.
aren’t adjusted.
 Refer to your projector’s manual for more
information.
Touch isn’t accurate. The
pointer doesn’t appear
directly below your finger.
When you write on the
screen, your writing
appears at a slight distance
from the pen.
Your Smart Board isn’t
oriented properly.
Orient your Smart Board.
 To start the orientation, press and hold both
the Keyboard and Right-Click buttons on the
pen tray at the same time.
 Pick up a pen from the pen tray.
 Beginning at the upper-left corner of the
screen, touch the center of the target firmly
with the tip of the pen until the target moves
to the next point.
13
SMART
Board 600
and D600
Series
Symptom/Observation
The SMART software icon
doesn’t appear in the
Windows notification area
or the Mac Dock.
Cause
Solution
SMART Board Tools
isn’t running.
Start SMART Board Tools.
 For Windows computers, select Start >All
Programs >SMART Technologies >SMART Product
Drivers> SMART Board Tools.
 For Mac computers, select Finder >Applications
>SMART Product Drivers >SMART Board Tools.
SMART Product Drivers
aren’t installed.
Install SMART Product Drivers on your computer.
 For details about installing SMART Product
Drivers, see Installing SMART software on page
22 of the User’s Guide.
14
SMART
Board 600
and D600
Series
Symptom/Observation
No pointer is visible on the
screen, and when you touch
the screen, a colored line
appears.
Cause
Solution
A pen is missing or isn’t
positioned properly in
its pen tray recess.
 Replace the missing pen.
 Place a sticky note over the sensor in the empty
tray.
Your pen, dry erase
marker, or old style
(black) SMART pen
doesn’t reflect infrared
light and the pen tray
sensors are unable to
detect it.
 Wrap light-colored tape on the pen to make it
more reflective.
15
SMART
Board 600
and D600
Series
Symptom/Observation
Cause
Solution
The pointer snaps back to one
location when you lift the pen
or your finger from the screen.
The resistive surfaces are  Gently pull the front sheet away from the
in constant contact at the
back sheet using a piece of tape or a small
location to which the
suction cup.
pointer returns. An object  If the problem goes away while you pull but
that hits or presses on the
returns when you release the tape or suction
front sheet, leaving a
cup, you might have to return your Smart
permanent depression,
Board for repair.
can cause this issue.
The pointer moves erratically
or gaps appear when you draw
with the pen.
The USB power from your
laptop, computer or USB
extender is too low to
power your Smart Board.
 Substitute another computer.
or
 Eliminate or substitute the USB extender.
or
 Install a powered USB hub.
16
SMART
Board 600
and D600
Series
 The Help Center contains links to a wide range of information, including
procedures, concepts, help with applications, SMART tool descriptions,
troubleshooting hints and more.
 Access the Help Center by pressing the Help button on the pen tray, using
the SMART software icon in the Windows notification area or Mac Dock,
or accessing this link:
http://onlinehelp.smarttech.com/english/windows/help/notebook/11_4_0/Ind
ex.htm#cshid=index
17
SMART
Board 600
and D600
Series
 SMART Training and Professional Development offers free
learning resources, hands-on lessons and information on how
to get more training.
http://www.smarttech.com/Training
 SMART Technical Support Center can offer assistance as well.
http://smarttech.com/Home+Page/Support/Browse+Support
18
SMART
Board 600
and D600
Series
Reading Materials:
 SMART Board Basics for Teachers
http://www.brighthubeducation.com/teaching-methods-tips/68850-how-to-use-a-smartboard-basics/#imgn_0
 Smart Notebook Training Beginner Session
http://centerville.k12.in.us/11%20computing%20initiative/pdf/NB11_LWB_%20Beginner.pdf
19
SMART
Board 600
and D600
Series
Videos:
 Complete SMART Board Tutorial
http://www.teachertube.com/video/complete-smart-board-tutorial-167098
 Fuse School Smart Board tutorials
https://www.youtube.com/results?search_query=Fuse+School+Smart+board

similar documents