Services & Solutions - Prairie Dog

Report
Horizontal Boring Machines
Made in THE USA!
http://www.undergroundequip.com
Services & Solutions
Authorized Dealers for Middle East,
Pakistan and Afghanistan
Tel: +92 51 250 4226
Fax; +92 51 252 5677
Email: [email protected]
Advantages of Prairie Dog Boring Machines
• Small, lightweight and inexpensive compared to competitive products
• Carbide tipped bits and Back Reamers allow the machine to handle boring through
the toughest conditions (including rocks)
• Very low operating costs
• Easy to operate, 1-2 operators can handle and operate the machines (except for
the heavier models)
• Ideal machines for non destructive boring with Low Environmental Impact, No road
cuts required.
• Sturdy Frames and long operational life
• Operates Above or Below Ground
• Best suited for :
• Laying water and sewerage lines
• Electrical conduits and wires
• Irrigation lines and conduits/pipes
• Telephone lines
• Gas lines
• Parks
Criteria for selection
The machines are sorted on the basis of bore dia, bore length and engine power
Weight
Bore
Dia
Bore
Length
Engine
Power
140HW
26 lb
2”-5”
50 feet
1.4 HP
Hand held, Two cycle Engine sealed spur gear with
centrifugal clutch
500RTW
135 lb
2”-6”
100 feet
5.5 HP
Wheel Mounted, Sealed spur gear with centrifugal clutch
500TW
125 lb
2”-6”
100 feet
5.5 HP
Rail Mounted, Sealed spur gear with centrifugal clutch, rack
and pinion advance
700TWA
325 lb
2”-14”
150 feet
9 hp
Rail Mounted, Rotary vein Air Motor, Planetary Transmission
with Forward and Reverse Rack & Pinion advance
900RTW
210 lb
2”-14”
150 feet
8.5 hp
Wheel Mounted, Planetary Transmission with Forward and
Reverse. Rack & Pinion advance
900TW
235 lb
2”-14”
150 feet
8.5 hp
Rail Mounted, Planetary Transmission with Forward and
Reverse. Rack & Pinion advance
1200TW
295 lb
2”-24”
200 feet
11 HP
Rail Mounted, Planetary Transmission with Forward and
Reverse. Rack & Pinion advance
1800TW
395 lb
3”-28”
300 feet
18 HP
Twin Cylinder Engine, Electric Start, Planetary Transmission
with forward and reverse. Rack & Pinion advance
Model
Type
How it works- Simple 7 step procedure
Step 1:
Dig trenches on either side of the road up to desired depth, one trench to
accommodate the machine and the other for come-out hole.
Come out hole
Trench for machine
Step 2:
Lower the machine into the trench and attach the first Drill Rod and Pilot Bit at the
end. Attach the water hose and start engine. Start moving the machine forward.
Step 3:
As each joint of Drill Rod is pushed into the ground a new one is added behind.
Step 3: (Contd..)
Keep on adding Drill Rods until the Pilot Bit reaches the come-out hole.
Step 4:
Remove the Pilot Bit and screw on the Backreamer
Step 5:
Start moving the machine backwards and start removing the Drill Rods as it becomes
completely exposed (at machine end)
Step 6:
Once the Backreamer reaches the start point cleanup the hole with a Pull-plate (if
required).
Step 7:
Slide in the pipe while the hole is still lubricated with slush
Note: The above steps are for illustration purpose only. Please read the user manual and safety instructions (supplied with the machine) before operating.
Thank You
For further information please contact:
Services & Solutions
Authorized Dealers for Middle East,
Pakistan and Afghanistan
Tel: +92 51 250 4226
Fax; +92 51 252 5677
Email: [email protected]

similar documents