High Mount 360° (6)

Report
01 August 2013
The information in this presentation is
confidential and proprietary, and may not be
used, reproduced or distributed without the
express written permission of
Acuity Brands Lighting, Inc.
© 2013 Sensor Switch
Overview
LSXR High Mount Sensor
Interchangeable Lenses
• Integrated Snap-Fit Bracket
• Single or Two-Pole Relay/Switch
• Dimming Output *
• Occupancy / Vacancy
• Passive Infrared (PIR)
• Photocell for Daylight Harvesting
• Reversible Line / Load Wires
•
* Single Pole model only
ENVIRONMENTAL SPECS:
Operating Temp:
Standard: 14° to 122° F (-10° to 50° C)
LT Option (PIR): -40° to 122° F (-40° to 50° C)
Relative Humidity:
Standard: 20 to 75% non-condensing
LT Option: 20 to 90% non-condensing
(electronics coated for corrosion resistance)
© 2013 Sensor Switch
Single Pole Model Numbers
COMMON MODEL NUMBERS
Model #
CI Code
LSXR 6
LSXR 10
LSXR 9
LSXR 50
LSXR 610
LSXR 650
219EP4
219EP7
219EP6
219EP8
219EJ9
219EP9
Description
High Mount 360° Sensor - Fixture Mount, Interchangeable Lens, Line Voltage, Passive Infrared
Low Mount 360° Sensor - Fixture Mount, Interchangeable Lens, Line Voltage, Passive Infrared
Small Motion 360° Sensor - Fixture Mount, Interchangeable Lens, Line Voltage, Passive Infrared
High Mount Aisle Way Sensor - Fixture Mount, Interchangeable Lens, Line Voltage, Passive Infrared
High Mount & Low Mount 360° Sensor - Fixture Mount, Interchangeable Lens, Line Voltage, Passive Infrared
High Mount 360° & High Mount Aisle Way Sensor - Fixture Mount, Interchangeable Lens, Line Voltage, Passive Infrared
© 2013 Sensor Switch
Single Pole Model Numbers
COMMON MODEL NUMBERS
Model #
CI Code
LSXR 6
LSXR 10
LSXR 9
LSXR 50
LSXR 610
LSXR 650
219EP4
219EP7
219EP6
219EP8
219EJ9
219EP9
Description
High Mount 360° Sensor - Fixture Mount, Interchangeable Lens, Line Voltage, Passive Infrared
Low Mount 360° Sensor - Fixture Mount, Interchangeable Lens, Line Voltage, Passive Infrared
Small Motion 360° Sensor - Fixture Mount, Interchangeable Lens, Line Voltage, Passive Infrared
High Mount Aisle Way Sensor - Fixture Mount, Interchangeable Lens, Line Voltage, Passive Infrared
High Mount & Low Mount 360° Sensor - Fixture Mount, Interchangeable Lens, Line Voltage, Passive Infrared
High Mount 360° & High Mount Aisle Way Sensor - Fixture Mount, Interchangeable Lens, Line Voltage, Passive Infrared
© 2013 Sensor Switch
Two-Pole Model Numbers
© 2013 Sensor Switch
Lens Model Numbers
COMMON MODEL NUMBERS
Lenses
LENS 6
LENS 10
LENS 9
LENS 50
High Mount 360° Lens Assembly for LSXR, Qty 1
Low Mount 360° Lens Assembly for LSXR, Qty 1
Small Motion 360° Lens Assembly for LSXR, Qty 1
High Mount Aisleway Lens Assembly for LSXR, Qty 1
© 2013 Sensor Switch
219P30
219P31
219P32
219P33
Physical Description
4.0”
.75”
Side
3.75”
•
•
•
•
3.75 H x 2.5 W x 4 D
(9.5cm x 6.4cm x 10.2cm)
Weight - 6 oz
Silicone Free & RoHS Compliant
4 Lens Options
 High Mount 360° Lens (6)
 High Mount Aisleway Lens (50)
 Small Motion 360°Lens (9)
 Low Mount 360° Lens (10)
3.0”
3.25”
2.5”
© 2013 Sensor Switch
Bottom
LSXR Bottom
½” Chase Nipple Mounting
Fits Fixture Knockout
(⅞“ Hole)
Screwdriver Slot
Removable
Lens Assembly
2.25” x 2.25”
LED Indicator
Programming/Switch
Push-Button
Screwdriver Slot
© 2013 Sensor Switch
LSXR Bottom Lens Removed
½” Chase Nipple
Fits Fixture Knockout
(⅞” Hole)
LED Indicator
PIR Detector
Photocell
(when present)
Programming / Switch
Push-Button
© 2013 Sensor Switch
LSXR Side
½“ Chase Nipple
Sensor Body
Lens Assembly
Programming / Switch
Push-Button
© 2013 Sensor Switch
LSXR Back
½” Chase Nipple
Sensor Body
Lens Assembly
© 2013 Sensor Switch
Mounting the LSXR
Fixture or Junction Box Mount
Note:
For safety reasons 2 phase versions should only
be fixture mounted.
© 2013 Sensor Switch
Mounting the LSXR
Remove knockout and feed wires through ⅞” hole
© 2013 Sensor Switch
Mounting the LSXR
Press chase nipple
firmly into hole
Tabs will compress and
snap into place when fully
inserted
© 2013 Sensor Switch
Mounting the LSXR
Tabs will secure
the sensor flush to
the fixture
© 2013 Sensor Switch
Lens Options
High Mount 360° (6)
Low Mount 360° (10)
Small Motion 360° (9)
2” x 2” Snap-in Lens assemblies
Ordered with Sensor or separately
© 2013 Sensor Switch
High Mount
Aisleway (50)
High Mount 360° Lens (6)
•
•
•
•
Best choice for 15 to 45 ft (4.57 to 13.72 m) mounting heights
15 to 20 ft (4.57 to 6.10 m) radial coverage overlaps area lit by
a typical high Mount fixture
Excellent detection of large motion (e.g. walking) up to a 35 ft
(10.76 m) mounting height
Excellent detection of extra large motion (e.g. forklifts) up to a
45 ft (13.72 m) mounting height
© 2013 Sensor Switch
Small Motion 360° Lens (9)
• Best choice for small motion (e.g. hand movements)
detection
• 360º conical shaped pattern
• Provides 12 ft (3.66 m) radial coverage when mounted to
standard 9 ft (2.74 m) ceiling
• 8 to 15 ft (2.44 to 4.57 m) mounting heights provide 10 to
20 ft (3.05 to 6.10 m) radial coverage
The gray ring differentiates
the 9 lens from the 10 Lens
© 2013 Sensor Switch
Low Mount 360° Lens (10)
• Best choice for large motion detection (e.g. walking)
• 360º conical shaped pattern
• Provides 24 ft (8.53 m) radial coverage when mounted to
standard 9 ft (2.74 m) ceiling
• 7 to 15 ft (2.13 to 4.57 m) mounting heights provide 16
to 36 ft (4.88 to 10.97 m) radial coverage
• Detection range improves when walking across beams
compared to into beams
© 2013 Sensor Switch
Mount Aisleway Lens (50)
Aisleway length
• Provides 50º bi-directional and 10º wide coverage
pattern
• 1.2x mounting height equals approximate detection
range in either direction
• Typical 40 ft (12.19 m) mounting detects 50 ft (15.24 m)
in either direction
© 2013 Sensor Switch
LSXR Lens Removal
Twist screwdriver slightly and
lens will pop free.
Insert flat blade screwdriver
Into slot
Pry lens clips loose by pushing
down on screwdriver handle
© 2013 Sensor Switch
LSXR Lens Installation
Snap lens into
sensor body
Align Lens with recess in
sensor body
Fit lens completely over
the recess
© 2013 Sensor Switch
LSXR Connections
LSXR Single Pole
With Dimming
LSXR Single Pole
No Dimming
LSXR Two-Pole
No Dimming
© 2013 Sensor Switch
LSXR Single Pole Connections
Black Load and Line Wires
Reversible
© 2013 Sensor Switch
HVOLT
RED Load and Line
Wires
Reversible
LSXR Single Pole Connections
© 2013 Sensor Switch
LSXR Single Pole w/Dimming Connections
Black Load and Line Wires
Reversible
Violet Dimming
Control Positive (+)
Gray Dimming
Control Negative (-)
White Neutral
HVOLT
RED Load and Line Wires
Reversible
LSXR Single Pole w/Dimming Connections
LSXR Single Pole 2-Phase Wiring w/ Dimming
Black Load and Phase A Line Wires
Reversible
Violet Dimming
Control Positive (+)
Gray Dimming
Control Negative (-)
White Phase B Line
© 2013 Sensor Switch
HVOLT
RED Load and Line Wires
Reversible
LSXR Single Pole 2-Phase Wiring w/ Dimming
© 2013 Sensor Switch
LSXR Two-Pole (2P) Connections
Black Load and Line Wires
Reversible
Pole 2 Blue Load and Line Wires
(on all models)
White Neutral
Reversible
© 2013 Sensor Switch
347VAC Model
RED Load and Line Wires
Reversible
LSXR Two-Pole Connections (DZ)
© 2013 Sensor Switch
LSXR Two-Pole(2P) Connections (SZ)
© 2013 Sensor Switch
LSXR Single Pole Sensor: Functional Block Diagram
© 2013 Sensor Switch
LSXR 2-Pole Sensor: Functional Block Diagram
© 2013 Sensor Switch
Programming LSXR
1.
Select the Function you want to program
•
•
2.
Select the new setting
•
•
3.
Press the push-button the number of times equal to the
function code. (i.e., 2 times = Occupancy Time Delay Function)
Once selected the LED will flash the current setting 3
times. You must enter a new setting prior to the 3rd time.
Press the push-button the number of times equal to the
new setting. (i.e. 3 times = 5 minutes)
LED Flashes the new setting (confirmation) 3 times.
You must enter a new setting prior to the 3rd time.
Programming complete!
© 2013 Sensor Switch
Programmable Functions
01 Not used
02 Occupancy Time Delay Pole 1
03 Occupancy Time Delay Pole 2
04 Minimum On Time (Lamp Maximizer)
05 Photocell Set-Point
06 Photocell / Dimming / 2-Pole Modes
07 Sunlight Discount Factor
08 Not Used
09 Restore Factory Defaults
10 Dimming Range Max (High Trim)
11 Dimming Range Min (Low Trim)
12 Switch (Button) Mode
13 Not used
14 Dual Zone Photocell Offset %
15 Dim to Off Time Delay
© 2013 Sensor Switch
Occupancy Time Delay (Pole 1)
Function 2
Index
Setting
1
Test Mode
2
30 seconds
3
2.5 minutes
4
5.0 minutes**
5
7.5 minutes
6
10.0 minutes*
7
12.5 minutes
8
15.0 minutes**
9
17.5 minutes
10
20.0 minutes**
11
22.5 minutes
12
25.0 minutes
13
27.5 minutes
14
30.0 minutes**
Definition:
Occupancy Time Delay (Pole 1) - The length of time
the sensor will keep the lights controlled by relay 1 on
and at full bright after it last detects occupancy,
assuming Minimum On Time (Function 4) has been
met.
Test mode - Disables Minimum On Time (Function 4),
sets Occupancy Time Delay (Function 2 & 3) to 30 sec,
and shortens the photocell transition times and
dimming rate. Mode will expire after 10 min or if
Function 2 is set back to a time delay.
*Default Settings, unless specified
in the model number
**Alternative Defaults
© 2013 Sensor Switch
Timers are 1.2x when used in
50Hz electrical systems.
(e.g., 10 mins is 12 mins in the UK)
Occupancy Time Delay (Pole 2)
Function 3
Index
Setting
1
N/A
2
30 seconds
3
2.5 minutes
4
5.0 minutes**
5
7.5 minutes
6
10.0 minutes*
7
12.5 minutes
8
15.0 minutes**
9
17.5 minutes
10
20.0 minutes**
11
22.5 minutes
12
25.0 minutes
13
27.5 minutes
14
30.0 minutes**
Definition:
Occupancy Time Delay (Pole 2) - The length of time
the sensor will keep the lights controlled by relay 2
(if present) on after it last detects occupancy,
assuming Minimum On Time (Function 4) has been
met.
*Default Settings, unless specified
in the model number
**Alternative Defaults
© 2013 Sensor Switch
Timers are 1.2x when used in
50Hz electrical systems.
(e.g., 10 mins is 12 mins in the UK)
Minimum On Time (LampMaximizer®)
Function 4
Index
Setting
1
0 minutes**
2
15 minutes*
3
30 minutes
4
45 Minutes
5
60 Minutes
Definition:
Minimum On Time – The length of time required
for lamps to be on in order to prevent short
cycling that reduces fluorescent lamp life. If
occupancy time delay expires prior to minimum
on time being satisfied, the lamps will remain on
until time has been met.
*Default Setting… changes to 0 minutes if occupancy
time delay is changed from 10 minutes
**Default setting for 5, 15, 20 and 30 minute
Occupancy Time Delay options
© 2013 Sensor Switch
Photocell Set-Point
Function 5
Index
Setting
1
Auto set-point
2
0.5 fc
3
1.0 fc
4
2.0 fc
5
4.0 fc*
6
8.0 fc
7
16.0 fc
8
32.0 fc
9
64.0 fc
Definition:
Photocell Set-Point - The target light level (as detected
at the sensor) that is to be maintained. Selecting Auto
(Setting 1) will initiate on/off cycling procedure where
sensor finds close-loop set-point.
Auto Set-point - Measures the Photocell with Lamps on
and with Lamps off and changes the Set-Point to the
difference. Assumes the contribution of Light by the
lamps is adequate for the space.
Note: Not applicable to non-photocell versions
*Default Setting
© 2013 Sensor Switch
Photocell (Single Relay Units with P (Photocell) Option)
Function 6
Definition:
Photocell Operational Setting - Describes the control the
photocell will have over normal occupancy / on / off operation
Index
Setting
1
Disabled
2
Full On/Off Ctrl*
Disable - Photocell does not affect lights
3
Inhibit Only Ctrl
Full On/Off Ctrl - Provides increased energy savings by
switching lights off during occupied periods with sufficient
daylight contribution from windows or skylights. Lights will be
switched back on if light level falls below set-point.
*Default Setting
Inhibit Only Ctrl - Photocell will prevent lights from initially
turning on if adequate daylight is available, but will not turn
lights off.
© 2013 Sensor Switch
Photocell (Units with ADC or ANL (Dimming) Options)
Function 6
Index
Setting
Definition:
1
Disabled
2
Automatic Dimming &
Switching (-ADC)*
3
Combination Dimming &
Switching Photocell w/
High/Low Occupancy
Operation (-ANL)*
Photocell Operational Setting - Describes the control the
photocell will have over normal occupancy / on / off
operation
Disable - Photocell does not affect lights
Automatic Dimming & Switching (-ADC) - Enables the
sensor during occupied periods to dim lights down and
then turn them completely off by opening the relay.
Combination Dimming & Switching Photocell w/
High/Low Occ. Operation (-ANL) - Provides maximum
energy savings by dimming and/or switching off lighting
during periods of sufficient daylight contribution from
windows or skylights. During unoccupied periods
without sufficient daylight lights are dropped to low dim
setting, insuring minimum light levels are maintained at
night.
*Default Settings for indicated options
© 2013 Sensor Switch
Photocell/Dimming/ 2-Pole Modes (Dual Relay (2P) Units - All Options)
Function 6
Index
Setting
1
Disabled
2
Standard Photocell
Option (-P)*
3
Single Zone (-SZ)
Photocell Option*
4
Dual Zone (-DZ)
Photocell Option*
5
Inhibit Only Ctrl
6
Alternating Off
Relays (-AO)*
7
Alternating Off
Relays w/
Photocell (-AOP)*
Definition:
Disable - Photocell does not affect lights
Standard Photocell Option (-P) - Photocell controls both relays together
with a single set-point.
Single Zone (-SZ) Photocell Option - Relay 1 controlled by photocell only,
relay 2 controlled by occupancy only.
Dual Zone (-DZ) Photocell Option - Relay 1 controlled according to setpoint, relay 2 controlled at fixed % higher as specified in Dual Zone
Photocell Offset Percentage (Function 14).
Inhibit Only Ctrl- Photocell will prevent lights from initially turning on if
adequate daylight is available, but will not turn lights off. Photocell
controls both relays according to set-point.
Alternating Off Relays (-AO)- Both relays close during periods of
occupancy, but only one opens during periods of vacancy. The relay left
closed is alternated in order to promote even lamp wear.
Alternating Off Relays w/ Photocell (-AOP) - Both relays close during
periods of occupancy, but only one opens during periods of vacancy or
high daylight. The relay left closed is alternated in order to promote even
lamp wear.
*Default Settings for indicated options
© 2013 Sensor Switch
Sunlight Discount Factor
Function 7
Index
Setting
1
x/1*
2
x/2
3
x/3
4
x/4
5
x/5
6
x/6
7
x/7
8
x/8
9
x/9
10
x/10
Definition:
Sunlight Discount Factor - Value used to improve the
tracking accuracy of a sensor with a photocell during
periods of high daylight. Decreasing the value will
lower the controlled level of the lights.
*Default Settings
© 2013 Sensor Switch
Restore Factory Defaults
Function 9
Index
Setting
1
Maintain Current*
2
Restore Defaults
*Default Settings
Definition:
Restore Factory Defaults - Returns functions to original
settings.
Maintain Current - Keeps all function settings in the
condition selected by the operator.
Restore Defaults - Returns all functions to Default
Settings.
46
© 2013 Sensor Switch
Dimming Range Max (High Trim)
Function 10
Index Setting
1
Min
2
1 VDC
3
2 VDC
4
3 VDC
5
4 VDC
6
5 VDC
7
6 VDC
8
7 VDC**
9
8 VDC**
10
9 VDC**
11
10 VDC*
Definition:
Dimming Range Max (High Trim) – The maximum
output level of a sensor with dimming. Default is
"10 VDC" unless indicated in model number.
Once met, lights resume following occupancy time delay
*Default Settings
**Alternate Options
for Default setting
© 2013 Sensor Switch
Dimming Range Min (Low Trim)
Function 11
Index Setting
1
Min*
2
1 VDC**
3
2 VDC**
4
3 VDC**
5
4 VDC**
6
5 VDC**
7
6 VDC**
8
7 VDC
9
8 VDC
10
9 VDC
11
10 VDC
Definition:
Dimming Range Min (Low Trim) – The minimum
output level of a sensor with dimming Default is
"Min" unless indicated in model number.
*Default Settings
**Alternate Options
for Default setting
© 2013 Sensor Switch
Switch (Button) Mode
Function 12
Index
Setting
1
Disabled*
2
Enabled
*Default Settings
Definition:
Switch (Button) Mode – When enabled, mode
allows user to switch the relay by pressing the
push-button for test purposes (e.g., in order to
test wiring). Note there is a short delay after
pushing the button before the relay switches.
© 2013 Sensor Switch
Dual Zone Photocell Offset %
Function 13
Index
Setting
1
110%
2
120%*
3
130%
4
140%
5
150%
6
160%
7
170%
8
180%
9
190%
10
200%
Definition:
Dual Zone Photocell Offset % – Relative value of
photocell set-point that is used to control relay 2.
Applies only to dual relay (2P) units with the -DZ
option.
50
*Default Settings
© 2013 Sensor Switch
Dim to Off Time Delay
Function 15
Definition:
Dim to Off Time Delay – An extended length of
time after the Occupancy Time Delay (Function
2) has expired and lighting is dimmed to the low
dimming range setting before the relay opens.
Applicable to dimming versions only.
Index
Setting
1
Disabled*
2
30 seconds
3
2.5 minutes**
4
5.0 minutes
5
7.5 minutes
6
10.0 minutes
7
12.5 minutes
*Default Settings
8
15.0 minutes
** Default Settings for -HL Option
9
17.5 minutes
10
20.0 minutes
11
Infinite
Timers are 1.2x when used in
50Hz electrical systems.
(e.g., 10 mins is 12 mins in the UK)
© 2013 Sensor Switch
Summary
Questions?
© 2013 Sensor Switch

similar documents