Innovation - AHK Serbien

Report
MIG Building Materials Program
MIG-WDF
Technologies for interior walls,
ceilings and facades
Leading by
Innovation
Belgrad , 21.10.2014
1
WDF focus
The WDF program offers:
• Up to date, smart, healthy and cost efficient solutions for
specific problems of interior walls, ceilings and facades:
• Key issues:
•
•
•
•
•
•
Reduction of energy consumption
Healthy and comfortable interior climate
Humidity management
Action against mold, mildew, algae and corrosion
Highly UV-resistant
Bright facades
Leading by
Innovation
Belgrad , 21.10.2014
2
WDF fields of actions
Exterior walls (about 35% of
heat losses) Reduces heat loss
in cold climate and
overheating in hot climate,
dehumidification, clean longlife facades
Roof (about 20% of heat
losses) Reduces heat
loss through ceilings.
Basement (about 15%
of heat losses) Reduces
heat loss, desiccation of
wet walls, removes
mold, rehabilitation
after storm flooding
Belgrad , 21.10.2014
Interior: Healthy and
comfortable climate
without molds, dust and
bad smells
Leading by
Innovation
3
WDFT product range
MIG-FPS (Facade Protection System) and MIG-CC (Comfort Coating) together
with MIG-Therm M65 and MIG-Hydro PFZ-X dehumidifying mortar
In addition, MIG has developed a complementary finely tuned product
range for particular requirements, situations and wall compositions like MIG262 a renovation mortar and glue and final plaster
By combination of these perfectly compatible products, you can resolve
problems in new and existing buildings that until now where difficult or
impossible to master.
Leading by
Innovation
Belgrad , 21.10.2014
4
WDF product groups
The product can be divided into 5 main groups:
1. MIG-CC Comfort Coating for walls and ceilings improves room climate
noticeable, is IR-reflecting and influences the moisture management
2. MIG-FPS is a waterproof facade protection system with extreme high
UV-resistance, brilliant reflecting optic, corrosion and mould inhibiting.
It can be used with different primers for different surfaces.
3. Under advanced development: MIG bactericide coatings, MIG
abrasion resisting and corrosion inhibiting industrial coatings, MIG
transparent and semi-transparent coatings.
4. The HYGRO program (= HYGROmetric control + HYGienic)
• Anti-humidity and anti-mould products …
5. Complementary MIG products which allow to achieve complex wall
compositions with high quality: e. g. Exterior insulation walls,
Leading by
rehabilitation of existing and historic buildings…
Innovation
Belgrad , 21.10.2014
5
WDF products 1
MIG-CC Comfort Coating:
Multi-functional coating for interior rooms:
• here: walls and ceilings
• Reflection of IR-heat radiation and hygrometric management. Water
vapour permeability sd = 0.04 m
• Prevention of mould, mildew, anti-allergenic and anti-odor properties,
reduction of dust-thermic
• registered German ecologic certification, no smell (No.: ID 0514 - 33310
– 001 UL ECO-INSTITUT)
• Certification of non radioactive components (IMPS Institut für
Leading by
Medizinische Physik und Strahlenschutz)
Innovation
Belgrad , 21.10.2014
6
WDF – FPS products 1
• MIG-FPS Facade Protecting System:
Multifunctional facade coating :
• Liquid water transmission rate, w24 = 0.04 kg/m²h0,5
• Protection against overheating by solar radiation
• Protection against water infiltration combined with high vapour
transmission: Demoisturizing, prevention of algae, stains and corrosion
• Brilliant color rendering by IR-Reflection
• Durability, Self cleaning properties
• Very high UV-resistance
• Burning class A2
• Low maintenance facade retain their attractive appearance and keeps the
reseller value up
Leading by
Innovation
Belgrad , 21.10.2014
7
WDF products 2
Complementary products of the MIG-FPS and MIG-CC program:
• MIG - Primer
• Primer for porous substrates
• MIG - Primer Quartz
• Primer for difficult smooth substrates
• MIG - Embossed Stucco
• Stucco with 2 mm or 3 mm grain relief with infrared reflecting and
dehumidification properties. May be combined with MIG-FPS coating for
even higher heat radiation properties
Leading by
Innovation
Belgrad , 21.10.2014
8
WDF – Technology products to come 1
MIG products in advanced development
• MIG-CC Antibacterial
Special formulation of MIG-CC with catalytic, non toxic and long lasting
anti-bacterial, anti-virus, anti-fungus agent. Tests show 99,9% of bacteria
eliminated. For hospitals, laboratories and all rooms with high hygienic
requirements.
• MIG - Smooth Stucco
MIG stucco is a fine grained mortar for smooth thin layer (1-3mm) coating.
Due to special ceramics, it has full infrared reflection capacity . It is also
formulated to keep the facade dry, clean and to prevent algae. Available in
different colors and in brilliant Super-White.
Leading by
Innovation
Belgrad , 21.10.2014
9
WDF products to come 2
MIG products in advanced development
• MIG - mineral glaze
Semi transparent glaze with features like MIG-FPS. The natural texture and
taint of concrete, stone, brickwork and fiber cement sheets shines
through.
• MIG - wood glaze
Semi transparent glaze for wood with features like MIG-FPS. Reduces the
variation of surface temperature and humidity and therefore the
formation of cracks. The UV-reflection prevents irregular graying. The
natural texture and taint of wood cladding, solid wood, OSB boards and
plywood shines through.
Leading by
Innovation
Belgrad , 21.10.2014
10
WDF – HYGRO products
• HYGRO – Demoisturizing mortar (PTZ-X):
• This mortar is based on a innovative technology that guaranties
an efficient demoisturizing of humid walls on the long term.
• HYGRO – Silicifying agent (VKM-concrete, stone, wood)
• This silicifying agent penetrates deeply into the supports, reduces
its hygroscopicity and hardens brickwork, concrete, stone
masonry and wood.
• HYGRO – Mould remover (SE – BIO)
• Based on organic, non toxic, non corrosive acids, this skin
tolerated mould remover removes not only mould, but also
mycotoxins and allergens.
Leading by
Innovation
Belgrad , 21.10.2014
11
WDF-Product Line
• MIG - THERM M 65, pure mineral base
• Highly insulating light mortar with fiber reinforcement for lightweight
insulating masonry < 0,10 W/mK; special application for high
insulating masonry with Lambda > 0.065 W/mK
• MIG – Lime-cement mortar (PTZ-KZP)
• Lime-cement mortar for masonry > 0,18 W/mK
• MIG – Reinforcement fiber plaster (PTZ-262)
• Reinforcement fiber plaster for exterior insulation.
• MIG – Reinforcement fabric (MW)
• MIG – Restoration plaster (SPZ)
• High quality fiber reinforced thin layer plaster for restoration.
• MIG – Adhesive mortar (PTZ-KLM):
• For fixing of exterior insulations
Leading by
Innovation
Belgrad , 21.10.2014
12
Calculating of the coupled heat and moisture
transfer in building elements
Calculation of the transient
development of temperature and
moisture by WUFI-Pro of
Fraunhofer IBP
Dr. Enver Akin – MIG
Leading by
Innovation
Belgrad , 21.10.2014
13
MIG-WDF: Comfort and health
MIG-CC: For a comfortable and healthy indoor climate:
• Higher surface temperatures, less difference between bottom and ceiling
• Moisture management, influences air humidity
• Prevention of mold, fungus, allergens and smells
• Eco-label registered
MIG-FPS: Long lasting well protected facades:
• Protection against rainwater penetration, reduced thermal stress (sun-shadow),
prevents micro-cracks
• Fast drying, prevention of algae, stains and corrosion
• High UV-resistant – brilliant facade optic
• Burning class A2
Especially in restoration, the results depend largely on the specific problem situations
• In specific problems, the WDF system comes in support with MIG-CC and MIG-FPS
products for optimized solution, even in very difficult cases: Restoration after
storm water flooding, wet cellars, heavy mold infestation…
Leading by
Innovation
Belgrad , 21.10.2014
14
MIG-WDF: Comfort and health
Leading by
Innovation
Belgrad , 21.10.2014
15
MIG-WDF: Comfort and health
Actual State
Lücking W12 d = 42.5 cm
Lambda = 0.12
Actual - plaster interior 1.5 cm - brickwork - plaster exterior 2.0 cm
U = 0.262 W/m²K Meeting the requirements of EnEV 2009 0.262 < 0.35
Heating mode for non-residential buildings > 19 °C – opaque building
components
Further values for the MIG-FDP and MIG-CC will be calculated according to DIN
EN ISO 6946:2008-04 using split heat transfer resistance as shown in Appendix A.
Leading by
Innovation
Belgrad , 21.10.2014
16
MIG-WDF: Comfort and health
MIG-FPS and MIG-CC for interior and exterior walls
Lücking W12 d = 42.5 cm
Lambda = 0.12
Actual - plaster interior 1.5 cm - brickwork - plaster
exterior 2.0 cm
U = 0.190 W/m²K Meeting the requirements of
EnEV 2009 -- 0.190 < 0.35
Heating mode for non-residential buildings > 19 °C –
opaque building components
U-value improvement 26 percent
Leading by
Innovation
Belgrad , 21.10.2014
17
MIG-WDF: Comfort and health
MIG-FPS and MIG-CC for interior and exterior walls +
MIG-ESP® M65 Supertherm plaster
Lücking W12 d = 42.5 cm
Lambda = 0.12
Actual - plaster interior 1.5 cm - brickwork - plaster exterior
2.0 cm
U = 0.166 W/m²K Meeting the requirements of EnEV 2009
-- 0.166 < 0.35
Heating mode for non-residential buildings > 19 °C – opaque
building components
U-value improvement 35 percent
Leading by
Innovation
Belgrad , 21.10.2014
18
MIG-WDF: Comfort and health
Restoration after
storm water
flooding, wet
cellars
Flood line
MIG-WDF Technology
Leading by
Innovation
Belgrad , 21.10.2014
19
Healthy Combination of MIG-FPS and MIG-CC + HYGRO
• The combination of FPS + CC and HYGRO products achieves
optimized wall construction through synergetic effects
• The protection against humidity and mould of HYGRO
products is perfectly complemented by the FPS + CC line:
–
–
–
–
Demoisturizing, high vapor transmission, stabilized air humidity
Higher surface temperatures
Photo-catalytic action
Inhibits the built up of mould, fungus, allergens
Leading by
Innovation
Belgrad , 21.10.2014
20
WDF examples: exterior insulation
MIG-FPS EXTERIOR
MIG-CC INTERIOR
Specific advantages for this type of construction:
• Infrared and daylight reflection:
 = Strongly reduced thermal stress of external skin,
prevention of micro-cracks, brilliant colors over a
long life-span, mix of light and dark colors possible
• High vapor transmission, fast drying:
 = Improved performance of insulation materials,
prevention of algae, stains and corrosion on the long
term
MIG reinforcement fabric
MIG PTZ 262
Insulation
MIG PTZ 262
Concrete
Belgrad , 21.10.2014
Plasterboard
Optional top coat with MIG stuccos:Leading by
A: MIG embossed stucco + MIG-FPSInnovation
B: MIG smooth stucco alone
21
MIG-WDF: Comfort and health
Leading by
Innovation
Belgrad , 21.10.2014
22
MIG-WDF: Comfort and health
Leading by
Innovation
Belgrad , 21.10.2014
23
WDF examples: lightweight brick masonry < 0,18 W/mK
MIG-CC INTERIOR
MIG-FPS EXTERIOR
MIG reinforcement fabric
MIG PTZ
262
MIG THERM 65
insulating mortar
Lightweight masonry
MIG-PTZ 18, MIG-262 or
Belgrad , 21.10.2014
plasterboard
Specific advantages for this type of
construction:
• Tests have shown that U-value of wall may be
improved significantly
• Infrared and daylight reflection:
 = Strongly reduced thermal stress of external
skin, prevention of micro-cracks, brilliant
colors over a long life-span
• High vapor transmission, fast drying:
 = Improved performance of insulation
materials, prevention of algae and stains on
the long term
• No electrostatic charging
 = No dust attraction, clean surface
Optional top coat with MIG stuccos:
A: MIG embossed stucco + MIG-FPS
B: MIG smooth stucco alone
Leading by
Innovation
Wall construction with insulating mortar MIG THERM 65
adapted to other types of masonry and for restoration
24
WDF examples: humid, porous, badly insulating masonry restoration
MIG-CC INTERIOR
MIG-FPS EXTERIOR
MIG reinforcement fabric
HYGRO
silicifying agent
MIG PTZ
262
MIG THERM 65
insulating mortar
HYGRO Dehumidifying
Belgrad , 21.10.2014
mortar
Specific advantages for this type of
construction:
• Efficient long lasting wall dehumidification,
prevention of mold and allergens
• Before application of HYGRO
dehumidification mortar: Efficient removal of
eventual mold layer by MIG-HYGRO mold
remover
• Solidification of porous masonry and
reduction of hygroscopicity by HYGRO
silicification agent
• High vapor transmission, fast drying:
 = Improved performance of dry materials,
prevention of mould, algae, stains and
corrosion
• No electrostatic charging
 = No dust attraction, clean surface
Optional top coat with MIG stuccos:
A: MIG embossed stucco + MIG-FPS
B: MIG smooth stucco alone
Leading by
Innovation
25
Examples
Leading by
Innovation
Belgrad , 21.10.2014
26
Examples
Leading by
Innovation
Belgrad , 21.10.2014
27
Thank you for your attention!
Leading by
Innovation
Belgrad , 21.10.2014
28
MIG
Material Innovative Gesellschaft mbH
Am Grarock 3
D-33154 Salzkotten
Phone: +49 (0) 52 58 – 9 74 82-0
Fax:
+49 (0) 52 58 – 9 74 82-29
www.mig-mbh.de
[email protected]
Leading by
Innovation
Belgrad , 21.10.2014
29

similar documents